要点
6/12は26.6°、50 %です。角度 = arctan(高さ / 12)、% = 高さ / 12 × 100。垂木長さは水平長さに勾配係数√(12² + 高さ²) / 12を掛け、6/12なら1.118倍です。
勾配・度・%
6/12は水平12 inに対して高さ6 inを意味します。Saskatchewan Indian Institute of Technologiesの木工マニュアルは比、角度、%で表しており、すべて同じ直線です。
角度はarctan(高さ / 水平長さ)、%は高さ / 水平長さ × 100です。12/12は上がる量と進む量が同じで45°、100 %です。100 %勾配は垂直ではありません。
| 勾配(高さ / 12) | 度 | % |
|---|---|---|
| 2/12 | 9.5° | 16.7 % |
| 3/12 | 14.0° | 25.0 % |
| 4/12 | 18.4° | 33.3 % |
| 5/12 | 22.6° | 41.7 % |
| 6/12 | 26.6° | 50.0 % |
| 7/12 | 30.3° | 58.3 % |
| 8/12 | 33.7° | 66.7 % |
| 9/12 | 36.9° | 75.0 % |
| 10/12 | 39.8° | 83.3 % |
| 12/12 | 45.0° | 100 % |
度からx/12へは角度の正接に12を掛けます。30°ならtan 30° × 12 = 6.93で約7/12。35°なら8.40/12です。
勾配係数: 垂木は水平長さの何倍?
垂木は水平長さと高さを直角辺とする三角形の斜辺です。水平12 in当たり√(12² + 高さ²) inあり、12で割ると勾配係数です。水平長さに掛ければ斜面長さが出ます。
面積にも同じ係数を使えます。屋根面積は水平投影面積 × 係数で、6/12なら11.8 %広くなります。
| 勾配 | 係数 | 水平12 in当たり垂木長さ |
|---|---|---|
| 2/12 | 1.014 | 12.17 in |
| 3/12 | 1.031 | 12.37 in |
| 4/12 | 1.054 | 12.65 in |
| 5/12 | 1.083 | 13.00 in |
| 6/12 | 1.118 | 13.42 in |
| 7/12 | 1.158 | 13.89 in |
| 8/12 | 1.202 | 14.42 in |
| 9/12 | 1.250 | 15.00 in |
| 10/12 | 1.302 | 15.62 in |
| 12/12 | 1.414 | 16.97 in |
マニュアルの例は4/12で水平16単位です。垂木線長さ12.65 in × 16 = 202.4 in(16 ft 10⅜ in)、高さ4 in × 16 = 64 inです。
勾配から垂木長さを求める
まず水平長さです。切妻の通常垂木は建物幅の半分から棟板厚の半分を引きます(Journal of Light Construction、Framing Workbook)。勾配係数を掛けてください。
JLCは棟の鉛直切断面から建物外面までを測るため、軒の出は含みません。軒先部分は軒の水平な出 × 単位長さで別に求めます。
メートル法: 幅8 m、35°なら水平4 m。係数1 / cos 35° = 1.221で垂木4 × 1.221 = 4.88 m、高さ4 × tan 35° = 2.80 mです。軒の出0.4 mなら斜面長さ0.49 mを加えます。
北米式: 幅24 ft、6/12なら棟板なしで水平12 ftです。12 × 1.118 = 13.42 ft、約13 ft 5 in(4.09 m)、高さ6 ft。棟板1½ inなら水平143.25 in、143.25 × 1.118 = 160.2 inです。軒12 inなら12 × 1.118 = 13.4 inを加えます。
理論上の長さです。切断分を見込み、全量を切る前に実際の下地で納まりを確認してください。
アスファルトシングルの最小勾配
ミネソタ州Hopkins市の要約によるIRC R905.2では、鉛直2・水平12(2:12)以上でシングルを認め、2:12から4:12は下葺き2重が必要です。
2:12は9.5°・16.7 %、4:12は18.4°です。2:12未満では別の屋根材が必要です。米国モデルコードなので、購入前に地域基準とメーカー要領を確認してください。
よくある質問
6/12は何度ですか?
arctan(6 / 12) = 26.6°、50 %、係数1.118です。
45°はどの勾配ですか?
12/12です。水平12 inに対し高さ12 inで、100 %です。
度からx/12にするには?
正接に12を掛けます。20°ならtan 20° × 12 = 4.37、約4.4/12です。
シングルの最小勾配は?
IRC R905.2では2:12(9.5°)で、2:12–4:12は下葺き2重です。米国モデルコードなので、メーカー要領も確認してください。
垂木長さに軒の出は含みますか?
JLC方式では含みません。棟の鉛直切断面から建物外面までとし、軒の水平な出 × 単位長さを加えます。
出典
- [1]Cutting Common Rafters (Framing Workbook, Training the Trades). Journal of Light Construction. Run of a common rafter on a full gable roof is half the building width minus half the ridge thickness; rafter length is measured from the top plumb cut to the building line and does not include the overhang.. 確認日: 2026年11月10日
- [2]Carpentry Refresher Program Manual, Topic 2: Gable Roof Components and Calculations (CC BY 4.0). Saskatchewan Indian Institute of Technologies. Slope as degrees, percent or unit rise in 12; total rise = unit rise × units of run; line length by Pythagoras; tail length = unit line length × overhang. Worked example: 4/12, 16 units of run gives 202.4 in (16 ft 10⅜ in) and 64 in of rise.. 確認日: 2026年11月10日
- [3]Asphalt shingles (IRC R905.2), city building department summary. City of Hopkins, MN. Asphalt shingles only on slopes of 2:12 or more; double underlayment from 2:12 to 4:12.. 確認日: 2026年11月10日