Skip to content
Yardox

Joist spacing for composite decking

Composite boards are softer than wood and sag between supports sooner, so the joist spacing is set by the board maker, not by habit. Once it is fixed, the board count, the joist count and the screws follow from simple arithmetic.

Updated November 10, 2026

Short answer

Trex recommends joists 16 in (406 mm) on centre for the decking surface, with every board spanning at least three joists. Leave at least 3/16 in (5 mm) between boards and fasten with two screws at every joist.

Calculate it

Decking calculator

Deck boards, cut plan, joists and screws.

Decking calculator →

How far apart should the joists be?

Trex publishes a chart of the allowed on-centre spacing for each product line and load rating, with 16 in and 24 in as the two values. Trex also states that a 16 in on-centre span is recommended for the decking surface when you want a stiffer deck. If you are unsure which line you are buying, 16 in is the number to plan with.

A board must also lie across at least three joists. Plan the framing so that no board is shorter than that.

16 in (406 mm) o.c.Gap ≥ 3/16 inBoardJoist
Trex decking: joists 16 in on centre, every board across at least three joists, two screws at each joist.

Boards laid at an angle need closer joists

The chart value applies to boards laid at 90° to the joists. When boards run at an angle, Trex reduces the maximum spacing like this:

Maximum joist spacing for angled boards (Trex), starting from a 16 in chart value
Board angle to joistsReductionSpacing from a 16 in chart value
90°none16 in (406 mm)
60°2 in (51 mm) less14 in (355 mm)
45°4 in (102 mm) less12 in (305 mm)
30°half of the chart value8 in (203 mm)

Diagonal patterns therefore need more joists, and the extra framing is a real cost. Count it before you decide on a herringbone or a diagonal lay.

Gaps between boards

Composite boards expand and contract with temperature, so they are never butted tight. Trex gives these gaps:

  • Side to side: at least 3/16 in (5 mm). In heavily wooded areas Trex asks for 3/8 in (10 mm). Never more than 1/2 in (13 mm).
  • End to end: 1/8 in (3 mm) when you install above 40°F (4.5°C), 3/16 in (5 mm) below that.

The side gap counts when you work out how many board rows fit. A Trex board is 5.5 in (140 mm) wide, so one row takes 5.5 + 3/16 = 5.6875 in (145 mm) of deck width.

Worked example: a 12 × 16 ft deck

Boards run along the 16 ft side and the joists run across, 16 in on centre. The boards are 16 ft (4.88 m) long, one of the lengths Trex offers next to 12 ft (3.65 m) and 20 ft (6.10 m).

  • Board rows across the 12 ft width: 144 in / 5.6875 in = 25.3, so 26 rows. In metric, 3.66 m / 0.145 m is also 25.2, so 26.
  • Joists along the 16 ft length: 192 in / 16 in = 12 spaces, so 13 joists.
  • Screws: every board crosses 13 joists with two screws each, so 26 rows × 13 × 2 = 676 screws.

The last row will probably be cut narrower than a full board. Buy for 26 full rows anyway and add your allowance for waste and miscuts on top. The decking calculator linked below does this sum and adds the waste for you.

Screws: how many and where

Trex says to always use two screws per joist. Keep each screw at least 1 in (25 mm) from the edge and from the end of the board, so the board does not split. Over a deck with 13 joists and 26 rows, that is 676 screws before waste, which is why a box count matters when you order.

Questions

Can I space composite deck joists 24 inches apart?

Only if the Trex chart for your specific product and load rating allows it. Trex recommends 16 in on centre for the decking surface, and that is the safer plan for a family deck.

How big a gap goes between composite deck boards?

At least 3/16 in (5 mm) between the long sides, 3/8 in (10 mm) in heavily wooded areas, and never more than 1/2 in (13 mm). Ends are spaced 1/8 in (3 mm) above 40°F (4.5°C) and 3/16 in (5 mm) below.

How many screws per board?

Two at every joist the board crosses. A 16 ft board over joists 16 in on centre crosses 13 joists, so it takes 26 screws.

How do I lay boards diagonally?

Reduce the joist spacing. From a 16 in chart value Trex takes off 2 in at 60°, 4 in at 45°, and halves the value at 30°.

How wide are Trex boards?

Trex square-edge and grooved boards are 5.5 in (140 mm) wide and 0.94 in (24 mm) thick in most lines, in lengths of 12, 16 and 20 ft (3.65, 4.88 and 6.10 m). The Select line is 0.82 in (20 mm) thick.

Calculate it

Decking calculator

Deck boards, cut plan, joists and screws.

Decking calculator →

Sources

  1. [1]Trex Decking Installation Guide (2026). Trex Company. Decking must span at least three joists; 16 in (406 mm) on centre for residential decks, less when boards run at an angle (p. 20, 22). Board ends always land on framing (p. 19). Side-to-side gap at least 3/16 in (5 mm) and no more than 1/2 in (p. 24).. Checked November 6, 2026
  2. [2]Trex Color-Match Composite Screw – installation instructions (DCM-0323). Trex Company. Always use two screws per joist; keep screws at least 1 in from board edges and ends.. Checked November 6, 2026
  3. [3]Trex product profiles. Trex Company. Square-edge and grooved boards 0.94 × 5.5 in (24 × 140 mm), lengths 12, 16 and 20 ft (3.65, 4.88 and 6.10 m).. Checked November 6, 2026