Skip to content
Yardox

How much vinyl siding to order: squares, panels, starter strip and J-channel

Siding is ordered in squares, trim in linear feet, and panels in boxes. The Vinyl Siding Institute manual gives one estimating method that covers all three.

Updated November 10, 2026

Short answer

Add up wall and gable areas, add 10 % and divide by 100 sq ft, because one square is 100 sq ft. A 40 × 30 ft house with 9 ft walls and two 6 ft gables is 1,440 sq ft, which is 1,584 sq ft with waste: 16 squares, or 8 cartons of 24 panels.

Calculate it

Siding calculator

Panels, boxes, starter strip, J-channel and corners.

Siding calculator →

Measuring walls and gables

The Vinyl Siding Institute (VSI) installation manual measures each wall as height times width and adds the walls together. A gable is a triangle, so its area is half the height times the width. The same half-height rule applies to dormers.

Siding is priced and sold by the square. One square covers 100 sq ft, which is 9.29 m². To convert a metric area, divide by 9.29 or multiply by 10.76 for square feet.

Windows, doors and waste

VSI says windows and doors are generally not deducted. Leaving them in covers part of the waste from cutting around them. Large openings such as a garage door or a sliding glass door can be subtracted.

On top of that, VSI says to add 10 % to all material estimates for waste, and more depending on roof pitch and other features of the house. Vertical siding waste depends on the wall height compared with the panel length.

Example in feet

House 40 × 30 ft, walls 9 ft high, two gables 30 ft wide and 6 ft high, siding with ABTCO Cedar Creek D4D panels (150 in long, about 8.33 sq ft each, 24 panels and 200 sq ft per carton).

Estimate by the VSI method
StepCalculationResult
Walls2 × 40 × 9 + 2 × 30 × 91,260 sq ft
Gables2 × ½ × 6 × 30180 sq ft
Total1,260 + 1801,440 sq ft
With 10 % waste1,440 × 1.11,584 sq ft
Squares1,584 / 10015.84, order 16
Panels1,584 / 8.33191 panels
Cartons191 / 248 cartons (192 panels)

Panel ends overlap by about 1 in, which shortens each panel's coverage slightly. With the overlap taken off, 1,584 sq ft needs 192 panels, which is still 8 cartons.

Example in metres

House 10 × 8 m, walls 2.7 m high, two gables 8 m wide and 2 m high, siding with Docke LUX Brus D6S (working size 3600 × 300 mm, 1.08 m² per panel, 16 panels per box).

  • Walls: 36 m perimeter × 2.7 m = 97.2 m². Gables: 2 × ½ × 2 × 8 = 16 m². Total 113.2 m².
  • With 10 % waste: 124.5 m². Panels: 124.5 / 1.08 = 115.3, so 116 panels.
  • Boxes: 116 / 16 = 7.25, so 8 boxes (128 panels). Seven boxes would leave you 4 panels short.

Starter strip, J-channel and corner posts

Trim is counted in linear feet or metres, not squares. VSI gives these rules:

  • Starter strip: the length around the whole base of the house. For the 40 × 30 ft house that is 140 ft (36 m for the metric one).
  • J-channel: measure around windows, doors and gables. Where two pieces join, overlap them by 3/4 in (19 mm). Count the pieces by the length the manufacturer sells.
  • Corner posts: where two lengths meet, cut 1 in off the nailing flange of the top piece and overlap by 3/4 in, leaving 1/4 in for expansion.
  • Utility (undersill) trim: estimate in linear feet for cut edges under windows and along the roof line.
  • Fasteners: VSI estimates the weight as sq ft × 0.005 lb for aluminium nails, or × 0.01 for roofing nails, staples or screws. For 1,584 sq ft that is 7.9 lb or 15.8 lb.

For fixing, VSI allows fasteners at most 16 in apart on horizontal panels, 12 in on vertical panels and 8 to 12 in on accessories. Keep panel seams at least 2 ft apart and leave 1/4 in of clearance inside receiving channels (3/8 in below 40 °F).

Questions

How many square feet is a square of siding?

100 square feet, or 9.29 m². The VSI manual uses this unit for ordering.

Do I subtract windows and doors?

Generally no. VSI leaves them in as an allowance for waste, and only suggests subtracting large openings such as garage doors or sliding glass doors.

How much extra siding should I order?

VSI says to add 10 % to all material estimates, and more depending on roof pitch and other house-specific factors.

How do I work out the starter strip?

Measure the length around the entire base of the house. A 40 × 30 ft house needs 140 ft.

How many panels are in a carton?

It depends on the product. ABTCO Cedar Creek D4D comes 24 to a carton covering 200 sq ft, and Docke LUX Brus D6S comes 16 to a box at 1.08 m² per panel.

Calculate it

Siding calculator

Panels, boxes, starter strip, J-channel and corners.

Siding calculator →

Sources

  1. [1]Vinyl Siding Installation Manual (2016). Vinyl Siding Institute. Estimating: walls height × width, gables ½ × height × width, windows and doors usually not deducted (large openings may be), add 10 % for waste, starter strip = length around the base, a square = 100 sq ft. Panel ends overlap about 1 in; fasteners at most 16 in apart on horizontal panels.. Checked November 6, 2026
  2. [2]Quick Tips for Installing Horizontal Vinyl Siding (2020). Vinyl Siding Institute. Overlap panels by 1 in; keep panel seams at least 2 ft apart; ¼ in clearance in receiving channels.. Checked November 6, 2026
  3. [3]ABTCO Cedar Creek D4D Double Dutchlap 4 in × 150 in, 24/box – product page. The Home Depot Canada. 8 in exposure, 150 in (12 ft 6 in) long, about 8.33 sq ft per piece, 24 pieces and 200 sq ft per carton.. Checked November 6, 2026
  4. [4]Docke LUX Brus D6S – product page. Docke. Working dimensions 3600 × 300 mm, working area 1.08 m², 16 pieces per box.. Checked November 6, 2026