Skip to content
Yardox

Rebar weight per foot and per metre, and how to count the bars

Rebar is sold by weight and by the bar, so you need both numbers: how heavy one metre is and how many bars the grid takes. Both come from a short table and one division.

Updated November 10, 2026

Short answer

A 12 mm ribbed bar weighs 0.89 kg per metre (CMC Poland), and a #4 bar weighs 0.668 lb per foot (Caltrans), which is 0.99 kg/m. The bar count in one direction is the span divided by the spacing, rounded down, plus one.

Calculate it

Rebar calculator

Bar count, length and weight for a slab mesh.

Rebar calculator →

Weight per metre and per foot

Nominal weight is the volume of steel times its density. For a round bar that is π × d² / 4 × 7850 kg/m³, with d in metres. For 12 mm that gives 0.888 kg/m, and the CMC Poland catalogue for ribbed bars lists 0.89.

To convert, 1 kg/m is 0.672 lb/ft and 1 lb/ft is 1.488 kg/m.

Ribbed bars, nominal mass (CMC Poland, EN 10080)
Diameterkg per metrelb per foot
8 mm0.400.27
10 mm0.620.42
12 mm0.890.60
16 mm1.581.06
20 mm2.471.66

US bar sizes #3 to #8 against millimetres

A US bar number is the nominal diameter in eighths of an inch: #3 is 3/8 in, #4 is 1/2 in, #8 is 1 in. Caltrans Bridge Design Details, Table 13.1.1, gives the weight of each size.

ASTM bars (Caltrans Table 13.1.1)
SizeDiameterlb per footkg per metre
#30.375 in (9.5 mm)0.3760.56
#40.500 in (12.7 mm)0.6680.99
#50.625 in (15.9 mm)1.0431.55
#60.750 in (19.1 mm)1.5022.24
#70.875 in (22.2 mm)2.0443.04
#81.000 in (25.4 mm)2.6703.97

The nearest metric bars are close but not the same: 10 mm weighs 0.62 kg/m against 0.56 for #3, and 12 mm weighs 0.89 against 0.99 for #4. Swapping one for the other changes the steel area, so that is the designer's decision, not a shopping shortcut.

How many bars a mesh needs

Bars in one direction sit across the other dimension of the slab. Take the span between the first and last bar (the slab dimension minus cover at both edges), divide by the spacing, round down and add one for the last bar.

Example: slab 4 × 3 m, 50 mm cover, 12 mm bars at 200 mm both ways, one layer. The bars run 3.9 m and 2.9 m between the covers.

  • Bars along the 4 m side, spread over 2.9 m: 2.9 / 0.2 = 14.5, round down to 14, plus one = 15 bars of 3.9 m = 58.5 m.
  • Bars along the 3 m side, spread over 3.9 m: 3.9 / 0.2 = 19.5, round down to 19, plus one = 20 bars of 2.9 m = 58 m.
  • Total 116.5 m × 0.89 kg/m = 103.7 kg, about 104 kg. There are 15 × 20 = 300 crossings to tie.

For two layers, double the length, mass and ties.

The same slab in feet

Slab 12 × 10 ft, 2 in cover, #4 bars at 12 in both ways, one layer. The bars run 11 ft 8 in and 9 ft 8 in between the covers.

  • Along the 12 ft side: 9.67 / 1 = 9.67, round down to 9, plus one = 10 bars × 11.67 ft = 116.7 ft.
  • Along the 10 ft side: 11.67 / 1 = 11.67, round down to 11, plus one = 12 bars × 9.67 ft = 116 ft.
  • Total 232.7 ft × 0.668 lb/ft = 155 lb.

Stock length and laps

CMC Poland lists 12 m as the standard bar length, with 6 to 18 m on request. In the metric example above, three 3.9 m bars fit in one 12 m bar (11.7 m) and four 2.9 m bars fit in one (11.6 m), so 15 bars take 5 stock lengths and 20 bars take 5, ten in all.

Where a run is longer than the stock bar, the bars overlap. The lap length comes from the structural design, usually as a multiple of the bar diameter, and there is no general number to use. Enter the lap from the drawings in the calculator, or leave it at zero if no lap is needed.

Questions

How much does rebar weigh per metre?

10 mm is 0.62 kg, 12 mm is 0.89 kg, 16 mm is 1.58 kg and 20 mm is 2.47 kg per metre, from the CMC Poland catalogue for ribbed bars.

How much does #4 rebar weigh per foot?

0.668 lb per foot, according to Caltrans Table 13.1.1. A #3 weighs 0.376 lb/ft and a #5 weighs 1.043 lb/ft.

What size in mm is #4 rebar?

Its nominal diameter is 1/2 in, which is 12.7 mm. The closest common metric bar is 12 mm, but it weighs less per metre (0.89 against 0.99 kg/m).

How do I count the bars in a grid?

Divide the span between the outer bars by the spacing, round down and add one. Do it once for each direction, then multiply each count by the length of its bars.

How far should rebar be spaced and how long should laps be?

Both come from the design drawings for your slab or footing. This guide gives no spacing or lap values because they depend on the load and the code.

Calculate it

Rebar calculator

Bar count, length and weight for a slab mesh.

Rebar calculator →

Sources

  1. [1]Bridge Design Details 13.1 Reinforcement, Table 13.1.1 ASTM Standard Reinforcing Bar Data (September 2025). California Department of Transportation (Caltrans). US bar sizes #3 to #11: nominal diameter and nominal weight in lb/ft (#3 0.376, #4 0.668, #5 1.043, #6 1.502 …).. Checked November 5, 2026
  2. [2]Mill products catalogue: ribbed reinforcing bars, EN 10080 B500B. CMC Poland. Mass per metre of ribbed bars, e.g. Ø10 0.62, Ø12 0.89, Ø16 1.58, Ø20 2.47 kg; matches π d² / 4 × 7850 kg/m³.. Checked November 5, 2026