Wallpaper calculator
Work out how many rolls of wallpaper to buy, strip by strip, with the pattern repeat and the match type taken into account.
Walls
For a whole room at one height, enter the perimeter.
An opening saves only the strips it covers whole. The short pieces above and below come from offcuts.
28 strips of 8.33 ft, 3 from each roll.
Rolls and pattern
From the roll label.
Pattern match
No pattern to line up: strips are cut to height plus trimming.
Brewster: 2 in at the top and 2 in at the bottom.
Printed on the paste pack. Leave empty to skip.
Add this calculator to your website
Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.
How to use it
- 01Enter the width and height of each wall. For a room with the same height all round, one entry with the perimeter is enough.
- 02Add doors and wide windows. Only openings at least one roll wide save a strip.
- 03Enter the roll width and length from the label, choose the match type and enter the pattern repeat.
- 04Keep the trimming allowance unless your paper needs more: 2 in (about 5 cm) at the top and at the bottom.
- 05Copy the list for the shop. Buy all rolls with the same batch number.
How it is calculated
We count whole strips, then how many strips each roll gives, because a roll cannot be used to the last centimetre.
- Strips
- strips = ⌈ wall width / roll width ⌉ − strips saved by openings
- Strip, free match
- strip = height + trimming
- Strip, straight match
- strip = ⌈ (height + trimming) / repeat ⌉ × repeat
- Strip, half drop
- strip = straight-match strip + repeat / 2
- Strips per roll
- ⌊ roll length / strip ⌋
- Rolls
- ⌈ strips / strips per roll ⌉
Dividing the wall area by the roll area undercounts: the offcut at the end of each roll is too short for another strip. Counting strips per roll avoids that.
With a straight match every strip must start at the same point of the pattern, so each strip uses a whole number of repeats. Christopher Farr Cloth adds half a repeat per strip for a half-drop pattern, because alternate strips start half a repeat lower.
An opening narrower than a roll saves nothing: the strip still has to run above and below it. Brewster recommends 2 in at the top and 2 in at the bottom of each strip for trimming.
Walls with different heights are counted on separate rolls, because offcuts from long strips rarely fit short ones exactly.
Worked example
Room with a 18 m perimeter, 2.5 m high, rolls 0.53 × 10.05 m
- Strip: 2.5 + 0.1 = 2.6 m. Strips per roll: ⌊10.05 / 2.6⌋ = 3.
- Strips: ⌈18 / 0.53⌉ = ⌈33.96⌉ = 34. Rolls: ⌈34 / 3⌉ = 12.
- With a 64 cm straight-match repeat: ⌈2.6 / 0.64⌉ × 0.64 = 3.2 m, still 3 strips per roll, 12 rolls.
- With the same repeat as a half drop: 3.2 + 0.32 = 3.52 m, only 2 strips per roll, 17 rolls.
Getting the order right
Check the batch number
Rolls from different print runs can differ slightly in shade. Buy all rolls from one batch and keep a label in case you need more.
Cut strips in order
With a half drop, cut odd and even strips from two rolls in turn. Each roll then keeps its pattern in step and you waste less.
Measure the tallest point
Ceilings and floors are rarely level. Measure the height in several places and use the largest.
Common mistakes
- Dividing wall area by roll area and ignoring offcuts.
- Ignoring the pattern repeat on patterned paper.
- Subtracting narrow doors and windows that still need full-width strips above and below.
- Forgetting the trimming allowance at the top and bottom.
- Buying rolls from different batches.
Questions
How many rolls of wallpaper for a 4 × 5 m room?
The perimeter is 18 m. At 2.5 m high with 0.53 × 10.05 m rolls and no pattern: 34 strips, 3 per roll, 12 rolls. Doors at least one roll wide reduce this by a strip each.
How do I account for the pattern repeat?
With a straight match, round each strip up to whole repeats. With a half drop, add another half repeat. A large repeat can cut the strips per roll from 3 to 2 and raise the roll count by half.
What is the difference between straight and half drop match?
With a straight match the pattern sits at the same height on every strip. With a half drop every other strip is shifted down by half a repeat.
How much extra should I add for trimming?
Brewster recommends 2 in at the top and 2 in at the bottom, 4 in per strip, which is about 10 cm.
Guides on this topic
- How many rolls of wallpaper do I need?
How to count wallpaper rolls: strip length, number of drops, pattern repeat and straight, offset or half-drop match, with a worked example.
Related calculators
Sources
- [1]How to Measure and Cut Wallpaper. Brewster Wallcovering. Strip length = wall height + 4 in: 2 in at the top and 2 in at the bottom for trimming.. Checked November 5, 2026
- [2]How to Calculate Wallpaper Quantities. Christopher Farr Cloth. Drops = wall width / roll width, rounded up; drop length in whole pattern repeats; a half-drop pattern adds half a repeat to each drop.. Checked November 5, 2026
- [3]FAQ: Ansatz (straight, offset and free match). Arte International. Definitions of straight match (pattern at the same height on every strip), offset match and free match.. Checked November 5, 2026
Formulas and sources last checked on November 5, 2026. How we calculate