本文へ移動
Yardox
この言語版はネイティブ話者による確認中です。表現が変わる場合があります。

Baluster spacing: the 4 inch rule and how to lay it out

Railing rules do not give a spacing. They give the largest opening, written as a ball that must not pass through. From that one number you can work out how many balusters a section needs and where each one goes.

更新日: 2026年11月12日

要点

Under the IRC no gap may let a 4 in (102 mm) sphere through. In England and Wales the limit is a 100 mm sphere, in Germany 12 cm. Count balusters with n = (span − limit) / (width + limit), rounded down, plus 1, then space them evenly.

計算する

Baluster calculator

How many balusters a railing needs and where to mark them, with the gap kept within code.

Baluster calculator →

What the rules say

The limit is written as a sphere because the opening that matters is the smallest one, between the widest parts of two balusters. The gap has to be smaller than the sphere, so a gap of exactly 4 in fails.

gap < 4 in4 in sphere36 in min.BalusterPost
The sphere test: no opening between balusters, or between a baluster and the post, may let the ball through.
Largest opening and guard height by rule
WhereLargest openingGuard heightWhen a guard is needed
United States, IRC R3124 in (102 mm) sphere36 in (914 mm)Open side more than 30 in (762 mm) above the floor or ground below
England, Wales, N. Ireland (NHBC 6.6.10)100 mm sphere900 mm on private stairs and landingsDrop of more than 600 mm
Germany (state codes, DIN 18065)12 cm90 cm on stairs, 110 cm above 12 m of fallSet by the state building code

The IRC has two exceptions on stairs. The triangle formed by the tread, the riser and the bottom rail may pass a 6 in sphere, and the guards on the open sides of stair treads may pass a 4 3/8 in sphere. On a deck or a landing the 4 in rule applies everywhere.

NHBC also asks that balustrading should not be easy for children to climb, so horizontal rails that work like a ladder are a poor choice on stairs and landings in the UK.

How many balusters per section

Measure the clear span between the faces of the two posts, not between their centres. With n balusters of width b in a span L there are n + 1 equal gaps, one more than the balusters, because the gaps at the posts count too. Each gap is (L − n × b) / (n + 1), and it must stay below the limit g. The fewest balusters that do this are:

  • n = (L − g) / (b + g), rounded down, plus 1.
  • Gap = (L − n × b) / (n + 1).
  • Centre to centre = gap + b.
  • First centre from the post = gap + b / 2.

When the division comes out as a whole number, the "plus 1" still applies. That is deliberate: the whole number would give gaps exactly equal to the limit, which fails the sphere test.

Worked example: a 6 ft deck section

A 72 in clear span between posts, 1.5 in square balusters, the IRC 4 in limit.

  • (72 − 4) / (1.5 + 4) = 12.36, rounded down 12, plus 1: 13 balusters.
  • Gap: (72 − 13 × 1.5) / 14 = 52.5 / 14 = 3.75 in, below 4 in.
  • Centre to centre: 3.75 + 1.5 = 5.25 in.
  • First centre: 3.75 + 0.75 = 4.5 in from the face of the post.

In metric, a 1500 mm section with 40 mm bars takes 9 bars under the German 12 cm limit, with gaps of 114 mm. Under the 100 mm sphere it takes 11 bars: (1500 − 100) / 140 is exactly 10, so the plus 1 matters, and the gaps come out at 88 mm.

Marking out on the rail

Mark the first centre from one post, then step along by the centre-to-centre spacing. On long sections small errors add up, so it is safer to mark the middle of the span first and work out towards both posts. A spacer block cut to the gap width keeps every gap the same while you fix the balusters.

Turned balusters are measured at their widest point, seen from the side. The gap at the narrow parts will be larger, but the sphere is stopped by the widest parts, so that is the width that goes into the sum.

よくある質問

What is the maximum spacing between balusters?

Under the IRC the opening must not let a 4 in sphere pass, so in practice the clear gap is a little under 4 in. In England and Wales the limit is a 100 mm sphere, in Germany 12 cm.

Do the gaps at the posts count?

Yes. The opening between the last baluster and the post must meet the same limit. Spacing evenly makes all gaps equal, including the ones at the posts.

How many balusters per foot of railing?

With 1.5 in balusters and gaps just under 4 in, one every 5.25 in, about 2.3 per foot. Count per section, because each post changes the number.

Is a 4 inch gap allowed?

No. The rule says a 4 in sphere must not pass, and a gap of exactly 4 in lets it through. Keep the gap below 4 in.

What about the gap under the bottom rail?

It is an opening too. On a deck or landing keep it within the same limit. On stairs the IRC allows the triangle between tread, riser and bottom rail to pass a 6 in sphere.

計算する

Baluster calculator

How many balusters a railing needs and where to mark them, with the gap kept within code.

Baluster calculator →

出典

  1. [1]Residential Stair Guide: visual interpretation of the IRC (2022). City of White Bear Lake Building Department. IRC R312.1.3: guards must not let a 4 in (102 mm) sphere pass; the triangle at tread, riser and bottom rail may pass 6 in; on the open sides of stair treads 4 3/8 in. Handrail height 34 to 38 in (R311.7.8.1).. 確認日: 2026年11月12日
  2. [2]Guard height and baluster spacing, IRC 2021 R312.1. Jaspector. Guards required on open sides more than 30 in above the floor or grade below; at least 36 in high.. 確認日: 2026年11月12日
  3. [3]NHBC Standards 6.6.10 Guarding. NHBC. Guarding where the drop is more than 600 mm; private stairs in England, Wales and Northern Ireland 900 mm high for flights and landings; balustrading must not let a 100 mm sphere pass and should not be easy for children to climb.. 確認日: 2026年11月12日
  4. [4]Geländer: Vorschriften und Normen. TÜV SÜD. Germany: at most 12 cm between bars, and at most 12 cm free space under a balcony railing; stair railings 90 cm high, 110 cm above 12 m of fall height; rules come from the state building codes and DIN 18065.. 確認日: 2026年11月12日