Skip to content
Yardox

Gutter and downspout calculator

Enter one side of the roof: the gutter length and how far the roof reaches back to the ridge. Get the number of downspouts, the gutter and pipe size and the lengths to buy.

Roof side

Imperial uses the Copper Development Association method: roof area times a pitch factor, drained per square inch of downspout for your city's 5-minute storm.

Eave with the gutter and the downspouts spread along it1 downspout40 ft

Gutter run

Along the eave, from one end of the gutter to the other.

Measured level from the eave to the ridge, not along the slope. For a shed roof, the full depth.

in 12

Steeper roofs catch more wind-driven rain, so the area is increased.

From the gutter to the ground, for the length of downspout pipe. Leave empty to skip.

Rain and downspouts

in/hr

5-minute intensity in inches per hour; replaces the city value.

Downspouts1 downspout
Add this calculator to your website

Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.

How to use it

  1. 01Work one side of the roof at a time: each eave with its own gutter.
  2. 02Enter the gutter length and the roof depth from the eave to the ridge, measured level on the plan, not along the slope.
  3. 03In imperial, pick the nearest city and the design storm, or type your own rainfall intensity, then pick the downspout. In metric, keep 300 l/(s·ha) or enter your local design rainfall.
  4. 04Read the number of downspouts, the sizes and the lengths of gutter and pipe to buy. Add the eave height to get the downspout pipe.

How it is calculated

A gutter has to carry the rain that falls on the roof behind it during a short, heavy storm. The two methods here come from a published design handbook (imperial) and a manufacturer table (metric).

Plan area
A = gutter length × roof depth
Design area (imperial)
A_d = A × pitch factor
One downspout drains
section (in²) × 1,200 / I (sq ft)
Downspouts (imperial)
n = max(⌈A_d / one⌉, ⌈L / 50 ft⌉)
Per downpipe (metric)
A / n ≤ table area × 300 / r

The Copper Development Association method multiplies the plan area by a factor for the pitch (1.00 up to 3/12, 1.05 for 4–5/12, 1.10 for 6–8/12, 1.20 for 9–11/12, 1.30 for 12/12). At a rainfall intensity of 1 in per hour one square inch of downspout drains 1,200 sq ft; the handbook lists the value for each city for 10-year and 100-year 5-minute storms. Each downspout should drain no more than 50 ft of gutter.

The downspout section is the actual inside area, not the nominal size: 4.80 sq in for a 2 × 3 in rectangular downspout, 10.31 for 3 × 4 in, 5.94 for 3 in round and 11.04 for 4 in round.

The Marley table gives, for 300 l/(s·ha) of rain, the roof plan area each gutter size can take: 25 m² for RG 75 with DN 53, 51 m² for RG 100, 100 m² for RG 125 and 159 m² for RG 150. With two downpipes each one takes half the area. For a different rainfall the areas scale with 300 / r.

Worked example

A 40 ft eave in Chicago, roof 20 ft deep, 4/12 pitch, 100-year storm

  1. Plan area 40 × 20 = 800 sq ft; design area 800 × 1.05 = 840 sq ft.
  2. Chicago, 100-year storm: 130 sq ft per sq in of downspout.
  3. A 3 × 4 in downspout drains 10.31 × 130 = 1,340 sq ft, so one is enough for the area, and 40 ft of gutter is under the 50 ft limit.
  4. Metric: a 12 m eave with a 5 m roof depth is 60 m² of plan area. One downpipe needs RG 125; with two, each takes 30 m² and RG 100 is enough.

Getting the order right

Put downspouts where water can go

Place them at corners or ends where the water can be led away from the foundation, and avoid making water flow around a corner of the gutter to reach a downspout.

Big roof, more downspouts

Adding a downspout is usually simpler than moving up a gutter size. In the metric table two downpipes halve the area each one drains.

Use the 100-year storm for valuable spaces

An overflowing gutter over a door, a terrace or a basement window does more harm. The 100-year figures give more capacity for the same roof.

Common mistakes

  • Measuring the roof along the slope. The method uses the plan area; the pitch factor already covers the slope.
  • Using the nominal size of a downspout. A 2 × 3 in downspout has only 4.8 sq in of actual section.
  • Draining a long eave with one downspout at the end. Past 50 ft of gutter, add a downspout even if the area allows fewer.
  • Forgetting the upper roof. Water from a higher roof that runs onto a lower one adds its area to the lower gutter.

Questions

How many downspouts do I need?

At least one for every 50 ft of gutter, and enough that their combined section can drain the design area for your local storm. A 3 × 4 in downspout drains about 1,340 sq ft in Chicago for a 100-year storm and about 3,700 sq ft in Seattle.

What size gutter for a 100 m² roof?

In the Marley table for 300 l/(s·ha), 100 m² of plan area on one downpipe needs RG 125 with DN 90 or 105. With two downpipes each one takes 50 m² and RG 100 is enough.

What is the capacity of a 2×3 vs a 3×4 downspout?

Capacity depends on the actual section: 4.80 sq in for 2 × 3 and 10.31 sq in for 3 × 4. Multiply by your city value in sq ft per sq in. The handbook recommends at least 7 sq in except for small roofs such as porches.

Does roof pitch matter?

Yes, in the imperial method: steeper roofs catch more wind-driven rain, so the plan area is multiplied by 1.05 to 1.30.

Where do the rainfall values come from?

The city values are from the Copper Development Association table of 5-minute storm intensities. 300 l/(s·ha) is the rainfall the Marley table is built on; local authorities publish design values for each place.

Guides on this topic

Sources

  1. [1]Copper in Architecture: 10.1 Hung Gutters and Downspouts Basics (Tables 10A, 10C). Copper Development Association. Area drained per square inch of downspout by city for 10-year and 100-year 5-minute storms (1,200 sq ft per sq in at 1 in/hr); plan area × pitch factor (level–3 in/ft 1.00, 4–5 1.05, 6–8 1.10, 9–11 1.20, 12 1.30); each downspout drains at most 50 ft of gutter; downspouts at least 7 sq in except small areas such as porches.. Checked November 10, 2026
  2. [2]Gutter sizing (Table 1-3, downspout areas). GutterSupply. Actual cross-section of downspouts: 2×3 in plain rectangular 4.80 sq in (nominal 6.00), 3×4 in 10.31 (12.0), 3 in round 5.94 (7.07), 4 in round 11.04 (12.57).. Checked November 10, 2026
  3. [3]Marley Dachrinnensysteme: Bemessungstabelle. Marley Deutschland. At a rainfall of 300 l/(s·ha): up to 25 m² roof plan area RG 70 or RG 75 with DN 53; up to 51 m² RG 100 with DN 75/90; up to 100 m² RG 125 with DN 90/105; up to 159 m² RG 150 with DN 105. Two outlets halve the area each one drains.. Checked November 10, 2026

Formulas and sources last checked on November 10, 2026. How we calculate