Roofing calculator
Work out the roof area from the plan and the pitch, convert pitch between x/12, degrees and percent, and count bundles, ridge caps, starter and underlayment.
Roof sections
If every slope has the same pitch, one section with the whole footprint is enough, whatever the roof shape: gable, hip or L-shaped.
Measure the footprint including the overhangs.
6/12 · 26.6° · 50 %
Total of all hips and valleys as drawn on the plan. Leave empty if none.
Shingles and underlayment
GAF Timberline: 3. Heavy shingles can need 4 or 5; check the wrapper.
Mike Guertin (Fine Homebuilding): about 1 % on a simple roof, 5 % or more with valleys.
The coverage printed on the roll, laps included. Leave empty to skip.
Ridge, hips and edges
Often about 35 ft per bundle; check the product.
Add this calculator to your website
Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.
How to use it
- 01Measure the footprint of the roof from below, overhangs included: length and width of the plan.
- 02Enter the pitch in the form you have it: 6/12, degrees or percent. The calculator converts between them.
- 03If parts of the roof have different pitches, add a section for each. Same pitch everywhere means one section is enough.
- 04Enter bundles per square from the wrapper and the extra for cuts. Add ridge, hip, eave and rake lengths for caps and starter.
- 05Copy the list for the supplier.
How it is calculated
When all slopes share one pitch, the roof area is the plan area times one factor, whatever the shape of the roof.
- Pitch
- r = rise / run = (x / 12) = tan θ = % / 100
- Slope factor
- k = √(1 + r²) = 1 / cos θ
- Roof area
- A = plan area × k
- Squares
- A × (1 + extra) / 100 sq ft
- Hip or valley
- true length = plan length × √(1 + r² / 2)
- Caps
- (ridge + hips) / length per bundle
Every point of a sloped plane sits above a point of the plan, and the plane is longer than its shadow by 1 / cos θ in the direction of the slope. That is why the same factor works for gable, hip and L-shaped roofs as long as all slopes share one pitch.
A hip between two equal slopes runs at 45° on the plan. Its true length is the plan length times √(1 + r² / 2).
GAF Timberline HD lists 3 bundles per square. Mike Guertin of Fine Homebuilding adds about 1 % on a simple roof and 5 % or more on a complex one with valleys, and estimates caps by length, typically about 35 ft per bundle.
Starter goes along the eaves; on the rakes it is optional. Underlayment rolls are counted on the roof area without the cutting extra.
Worked example
Plan 30 × 40 ft, pitch 6/12, 3 bundles per square
- r = 6 / 12 = 0.5; k = √(1 + 0.25) = 1.1180.
- Roof area: 1200 × 1.1180 = 1341.6 sq ft.
- With 5 % extra: 1408.7 sq ft = 14.09 squares.
- Bundles: 1408.7 / 33.33 = 42.3, so 43 bundles.
Getting the order right
Measure from the ground
The plan with overhangs is easier and safer to measure than the slopes. Count the overhangs on every side.
Check the pitch with a level
Hold a 12 in level horizontal against a rafter and measure down to it: that is the rise per 12 in.
Follow the minimum slope
Every shingle and sheet has a minimum pitch in its installation instructions. Lower slopes need a different product or extra underlayment.
Common mistakes
- Using the plan area without the slope factor.
- Forgetting the overhangs.
- Measuring hips on the plan and using that length for caps.
- Ordering by the square foot on bundles that cover less than a third of a square.
- Applying one factor to sections with different pitches.
Questions
How do I convert 6/12 pitch to degrees?
θ = atan(6 / 12) = 26.57°. As a percent it is 50 %. 12/12 is 45°, 4/12 is 18.43°, 8/12 is 33.69°.
How many bundles in a square?
Most shingles: 3 bundles per 100 sq ft. GAF Timberline HD lists 3. Some heavy shingles need 4 or 5; the wrapper says.
How much extra should I add?
Mike Guertin adds about 1 % on a simple roof and 5 % or more on a complex roof with valleys. Hips and many cuts need more.
Does the formula work for a hip roof?
Yes, if every slope has the same pitch: the roof area is the plan area times √(1 + r²), whatever the shape.
Guides on this topic
- How many bundles of shingles do I need per square?
Bundles per roofing square, how to turn a roof footprint into squares with the pitch factor, and how much starter and ridge cap to add, with worked examples.
Related calculators
Sources
- [1]Timberline HD Lifetime Shingles, technical data sheet (10/26/2015). GAF. 3 bundles per square (100 sq ft); exposure 5⅝ in; shingle 13¼ × 39⅜ in.. Checked November 5, 2026
- [2]Don't Fall Short on Shingles: How to Estimate Materials for Roofing Projects. Mike Guertin, Fine Homebuilding. Waste about 1 % on a simple roof, 5 % or more on a complex roof with valleys; starter along eaves (rakes optional); hip and ridge caps by length, a bundle typically caps about 35 linear ft; three bundles per square is most common, heavy shingles need four or five.. Checked November 5, 2026
Formulas and sources last checked on November 5, 2026. How we calculate