Laminate and vinyl calculator
Work out how many packs of laminate or vinyl planks to buy, plus underlay and skirting, and check the width of the last row before you start.
Rooms
Boards usually run towards the main window.
Only for skirting: no skirting goes across a doorway.
20 rows. The last row would be only 0.75 in, so cut the first row too: both edge rows 4.13 in.
Boards and packs
The visible width, without the tongue.
From the installation instructions: Quick-Step 8–10 mm, Pergo 3/8 in.
Quick-Step: if the last row would be less than 40 mm, cut the first row too.
Pack size
Printed on the pack label.
Lowe's recommends buying at least 10 % more than the floor area.
Underlay and skirting
Leave empty to skip. Underlay is counted on the net floor area.
Leave empty to get only the length. Assumes offcuts are joined on long walls.
Add this calculator to your website
Free for any website: paste this code where the calculator should appear. It keeps itself up to date, fits its height to the content and links back to the full page with the explanations.
How to use it
- 01Enter the room length along the boards and the width across them. Boards usually run towards the main window, so that the light falls along the joints. Add an L-shaped room as two rectangles.
- 02Enter the visible board width and length from the pack label, and the area or number of boards in one pack.
- 03Check the expansion gap and the narrowest edge row in your installation instructions. The calculator tells you whether the last row will be too thin and how wide to cut the first one.
- 04Leave at least 10 % extra for cuts and mistakes. Add the underlay roll size and skirting length if you are buying them too.
- 05Copy the list and take it to the shop. Check that all packs carry the same batch number.
How it is calculated
Packs come from the floor area plus an allowance; the rows come from the width of the room after the expansion gaps.
- Floor area
- S = L × W
- To buy
- S buy = S × (1 + extra)
- Packs
- packs = ⌈ S buy / area of one pack ⌉
- Rows
- rows = (W − 2 × gap) / board width
- Last row
- last = (W − 2 × gap) − full rows × board width
- If last < minimum
- first = last = (board width + last) / 2
- Skirting
- 2 × (L + W) − doorways
Laminate and vinyl float on the subfloor and move with temperature and humidity, so every installation guide asks for a gap at the walls: 8–10 mm for Quick-Step, 10–15 mm for HARO, 3/8 in for Pergo. That gap reduces the width you actually cover.
A last row only a few millimetres wide is hard to cut and click in. Quick-Step says that if the last row would be less than 40 mm, the first row should be cut too. We split the leftover so that both edge rows have the same width.
Underlay is counted on the net floor area. Skirting is the perimeter minus doorways; pieces assume that offcuts can be joined on long walls.
We round up only once, at the end, so rounding does not stack up.
Worked example
Room 5 × 3.5 m, boards 1380 × 192 mm, packs of 8 boards
- Rows: (3500 − 2 × 10) / 192 = 18.125, so 18 full rows and a last row of only 24 mm. That is under 40 mm, so cut the first and last rows to (192 + 24) / 2 = 108 mm each, 19 rows in total.
- Floor area 5 × 3.5 = 17.5 m²; with 10 % extra, 19.25 m².
- One pack: 8 × 1.38 × 0.192 = 2.12 m². 19.25 / 2.12 = 9.08, so 10 packs.
- Skirting: 2 × (5 + 3.5) − 0.9 = 16.1 m, which is 7 pieces of 2.4 m.
Getting the order right
Stagger the end joints
End joints in neighbouring rows must not line up. Instructions give a minimum offset: at least 30 cm for Quick-Step, 50 cm for HARO, 6 in for Pergo. Start each row with the offcut from the previous one when it is long enough.
Let the boards acclimatise
Keep the unopened packs in the room for the time the instructions state before laying, so that the boards reach the room temperature and humidity.
Measure at both ends
Walls are rarely parallel. Measure the room width at both ends and in the middle, and plan the rows on the widest figure.
Common mistakes
- Forgetting the expansion gap and pressing the floor tight against the walls.
- Entering the full board width including the tongue instead of the visible width.
- Leaving a sliver of a last row instead of trimming the first row as well.
- Lining up end joints in neighbouring rows.
- Buying packs from different batches, which can differ slightly in shade.
Questions
How many packs of laminate do I need for 20 m²?
Add the extra first: 20 × 1.10 = 22 m². Then divide by the area printed on the pack. For packs of 2.13 m² that is 10.3, so 11 packs.
How much extra laminate should I buy?
Lowe's recommends at least 10 % more than the floor area, for cuts and mistakes. Rooms with many corners, pipes or a diagonal layout need more.
How big should the expansion gap be?
Follow the instructions for your floor. Quick-Step asks for 8–10 mm, HARO for 10–15 mm and Pergo for 3/8 in on all sides. Large rooms may need more.
What if the last row is too narrow?
Cut the first row as well, so that both edge rows have the same width. Quick-Step does this when the last row would be less than 40 mm.
Guides on this topic
- How many boxes of laminate flooring do I need?
Boxes of laminate or vinyl plank for a room, how much waste to add, expansion gap, narrow last row and end joint offset, from Quick-Step, HARO and Pergo.
Related calculators
Sources
- [1]Installation instructions for Quick-Step laminate with Hydroseal technology. Quick-Step (Unilin). Expansion gap 8–10 mm; if the last row would be less than 40 mm, cut the first row too; end joints staggered at least 30 cm. Checked November 5, 2026
- [2]PERGO XP Install Instructions (2019_03_XP_SML). Pergo (Unilin). Expansion space 3/8 in on all sides; end joints offset at least 6 in; first piece at least 8 in long. Checked November 5, 2026
- [3]Installation instructions for laminate flooring with Top Connect (08/22). HARO. Expansion gap 10–15 mm; end joints offset at least 50 cm. Checked November 5, 2026
- [4]How to Install Laminate Flooring. Lowe's. Buy at least 10 % more flooring than you plan to use, for cuts and mistakes. Checked November 5, 2026
Formulas and sources last checked on November 5, 2026. How we calculate